Projector-to-Screen Distance: 100–150-Inch Chart

Summary
Projector-to-screen distance = throw ratio × image width. Distance charts for 100, 120 and 150-inch screens, worked examples, and short throw vs standard.
Projector-to-screen distance is worked out with one formula: distance = throw ratio × image width. A 100-inch 16:9 screen is about 2.2 metres wide, so a standard projector with a 1.5 throw ratio needs about 3.3 metres, while a 0.5-ratio short throw needs only about 1.1 metres. A short throw is the choice when that much distance is not available.
This guide helps you decide with numbers rather than guesswork: how to read the throw ratio on a spec sheet, a distance table by screen size, how to size the screen from where your audience sits, and when short throw genuinely solves the presenter-shadow problem. If you already have your room measurements and want to book a unit, Arental's projector rental service covers offices, campuses and events across Greater Jakarta, and the rates for each class are listed on the projector rental prices page.
What Is Throw Ratio, and Why Does It Decide the Projector Type?
Throw ratio is the relationship between the lens-to-screen distance and the width of the image it produces. A projector with a 1.5 throw ratio produces an image 1 metre wide from 1.5 metres away. The smaller the number, the closer the projector can sit for the same image size.
That number is what separates the three projector types. The boundaries are not fixed and vary slightly between manufacturers, but the usual reference points look like this:
| Type | Typical throw ratio | Distance for a 100-inch (16:9) screen | Usual mounting position | Example in the Arental catalogue |
|---|---|---|---|---|
| Standard | Roughly 1.2 to 2 | Roughly 2.7 to 4.4 m | Ceiling in the middle of the room, or a table behind the audience | Epson EB-X06/W06, Microvision MV-E46WL (1.48–1.78:1) |
| Short throw | Roughly 0.4 to 1 | Roughly 0.9 to 2.2 m | Table or low tripod near the screen, wall bracket | BenQ Short Throw (0.5–1.0 ratio) |
| Ultra short throw (UST) | Below about 0.4 | Tens of centimetres | Directly below or above the screen | Epson EB-810E/815E |
Many projectors have a zoom lens, so the throw ratio is written as a range, for example 1.48–1.78:1. It means that, for the same image, the projector can sit anywhere between its nearest and farthest distance. That range gives you room to manoeuvre when the ceiling mounting point is already fixed.
The Projector-to-Screen Distance Formula
Working out the distance takes just two numbers: the image size you want and the projector's throw ratio.
Step one: convert the diagonal size into width
Screen sizes are usually quoted in diagonal inches, while the distance formula uses width. The conversion depends on the screen aspect ratio:
- 16:9 (modern slides and video): width ≈ 0.87 × diagonal.
- 16:10 (many laptops and WXGA projectors): width ≈ 0.85 × diagonal.
- 4:3 (older formats and many tripod screens): width = 0.8 × diagonal.
One inch equals 2.54 cm. So a 100-inch 16:9 screen is 100 × 0.87 × 2.54 ≈ 221 cm wide, a 16:10 screen about 215 cm, and a 4:3 screen about 203 cm.
Step two: multiply by the throw ratio
Throw distance = throw ratio × image width. The table below does the maths for the sizes most often used in meeting rooms, classrooms and seminars (16:9 format, distance measured from the lens to the screen surface):
| 16:9 screen size | Image width × height | Ratio 0.5 | Ratio 0.8 | Ratio 1.5 | Ratio 1.8 |
|---|---|---|---|---|---|
| 70 inches | 1.55 × 0.87 m | 0.77 m | 1.24 m | 2.32 m | 2.79 m |
| 80 inches | 1.77 × 1.00 m | 0.89 m | 1.42 m | 2.66 m | 3.19 m |
| 90 inches | 1.99 × 1.12 m | 1.00 m | 1.59 m | 2.99 m | 3.59 m |
| 100 inches | 2.21 × 1.25 m | 1.11 m | 1.77 m | 3.32 m | 3.98 m |
| 120 inches | 2.66 × 1.49 m | 1.33 m | 2.13 m | 3.98 m | 4.78 m |
| 150 inches | 3.32 × 1.87 m | 1.66 m | 2.66 m | 4.98 m | 5.98 m |
The reverse: how big an image can you get from the distance you have?
If your room already limits the distance, flip the formula: maximum image width = available distance ÷ throw ratio. From 2.5 metres, a standard projector with a 1.5 ratio only produces an image about 1.67 metres wide, roughly 75 inches. A 0.5-ratio short throw at the same distance could throw a far larger image than any meeting room needs, so in practice the unit is moved closer to the screen, freeing up space for the table.
Brochure figures are sometimes measured from the front of the housing rather than the lens, especially on UST models. The difference is only a few centimetres, but at such short distances it shows. Once the model is confirmed, check it against the manufacturer's calculator or the projection calculator listed in the references.
A worked example: calculating projector-to-screen distance
Say a training room wants a 120-inch 16:9 screen and a zoom-lens projector with a 1.48–1.78:1 throw ratio.
1. Convert the diagonal into width: a 120-inch 16:9 screen is about 2.66 metres wide. 2. Multiply by the smallest ratio for the nearest distance: 1.48 × 2.66 ≈ 3.9 metres. 3. Multiply by the largest ratio for the farthest distance: 1.78 × 2.66 ≈ 4.7 metres. 4. Mount the projector somewhere between about 3.9 and 4.7 metres from the screen, measured from the lens. Outside that range, the image will be larger or smaller than 120 inches.
If the mounting point is already fixed, reverse the calculation. From 4 metres, a projector with a 1.5 ratio produces an image about 2.67 metres wide, roughly 120 inches at 16:9; from 3 metres, the result is about 90 inches.
Projector-to-Screen Distance for 100, 120 and 150-Inch Screens
The distance for the three most searched sizes can be read straight from the 16:9 table in the formula section above, from the 4:3 table below, and from the table of Arental fleet units, which uses their native 16:10 format.
Projector distance for a 100-inch screen
For a 100-inch 16:9 screen, which is 2.21 metres wide, a standard projector with a 1.5 ratio needs about 3.3 metres and a 1.3 ratio about 2.9 metres, while a 0.5-ratio short throw needs only about 1.1 metres. On a 100-inch 4:3 screen, the width is 2.03 metres, so a 1.5 ratio needs about 3.05 metres.
Projector distance for a 120-inch screen
A 120-inch 16:9 screen is 2.66 metres wide, so a projector with a 1.5 ratio needs about 4 metres, a 1.3 ratio about 3.45 metres, and a 0.5 short throw about 1.33 metres. On a 120-inch 4:3 tripod screen (2.44 metres wide), a 1.5 ratio needs about 3.66 metres.
| 4:3 screen | Image width | Ratio 0.5 | Ratio 1.3 | Ratio 1.5 | Ratio 1.8 |
|---|---|---|---|---|---|
| 100 inches | 2.03 m | 1.02 m | 2.64 m | 3.05 m | 3.66 m |
| 120 inches | 2.44 m | 1.22 m | 3.17 m | 3.66 m | 4.39 m |
| 150 inches | 3.05 m | 1.52 m | 3.96 m | 4.57 m | 5.49 m |
This 4:3 table applies when the image fills the width of a 4:3 screen, for example from an XGA projector. When 16:9 slides are shown on a 4:3 screen, the width still matches the screen, but the image is shorter and empty bands appear above and below it.
Distances for units in the Arental fleet
| Unit and throw ratio | 100-inch screen | 120-inch screen | 150-inch screen |
|---|---|---|---|
| BenQ Short Throw, 0.5–1.0 | 1.08–2.15 m | 1.29–2.58 m | 1.62–3.23 m |
| Epson EB-W06, 1.30–1.56 | 2.80–3.36 m | 3.36–4.03 m | 4.20–5.04 m |
| Microvision MV-E46WL, 1.48–1.78 | 3.19–3.83 m | 3.83–4.60 m | 4.78–5.75 m |
The first figure in each cell is the minimum distance (widest zoom) and the second the maximum distance (narrowest zoom), calculated with the 16:10 screen width that matches each unit's native resolution: 2.15 metres for 100 inches, 2.58 metres for 120 inches and 3.23 metres for 150 inches. The Epson EB-W06 throw ratio comes from Epson's official specifications; the other two units come from Arental's catalogue pages.
Minimum, maximum and ideal distance
The minimum and maximum distances are set by the lens zoom range: outside that range, the image size you want cannot be reached. The ideal distance is the point inside that range that keeps the projector out of walkways and its cables off the floor, usually a ceiling bracket in a fixed room or an operator's table behind the audience in a hall. For screens of 150 inches and up, a standard projector almost always sits behind the audience, while a short throw stays at the front, close to the screen.
How Big Does the Screen Need to Be for Your Room?
Before calculating distance, settle the image size. The rule of thumb we use on the projector screen rental page: image height should be roughly one sixth of the distance to the farthest viewer.
- Back row at 4.5 metres: image height about 0.75 m, equivalent to a 60-inch 16:9 screen.
- Back row at 6 metres: image height about 1 m, equivalent to an 80-inch screen.
- Back row at 9 metres: image height about 1.5 m, equivalent to a 120-inch screen.
Putting the two together: a 7-metre meeting room with the screen at one end and the back row 6 metres away needs an image of around 80 inches. A standard projector with a 1.5 ratio has to sit about 2.7 metres from the screen, which is above the middle of the meeting table. If the ceiling can take a bracket, that is not a problem. If the projector has to sit on the table, it ends up in the middle of the attendees, and anyone who stands up cuts through the beam. That is where short throw starts to make sense.
When Is Short Throw the Answer?
Shallow rooms
Small meeting rooms, huddle rooms or classrooms where tables and chairs fill nearly the whole floor leave no distance for a standard projector. A short throw produces a large image from about a metre away, so the image stays readable from the back seats.
The presenter stands close to the screen
Shadows appear when the presenter stands between the lens and the screen. A standard projector on a central table will almost certainly cast a shadow every time the presenter points at a slide. A short throw placed near the screen projects at a much steeper angle, so the strip of floor in front of the screen that sits in the light path is far narrower.
The ceiling cannot take a bracket
Leased buildings often prohibit drilling into the ceiling, or the ceiling is too high for a standard bracket. A short throw on a small table near the screen avoids installation work, and the HDMI cable it needs is shorter too. Cable and adapter choices are covered in our guide to HDMI and USB-C presentation connectors.
Exhibition booths and interactive classrooms
In a booth, visitors keep walking in front of the screen. In an interactive classroom, the teacher writes or points directly on the screen. Both suit a short throw best, or a UST if the available distance is only tens of centimetres.
When Is a Standard Projector the Better Fit?
Rooms with enough distance
Training rooms, halls and large meeting rooms generally have enough depth. In rooms like these, a standard projector produces a large image without moving close to the screen, and the presenter stands beside the screen without crossing the beam.
Permanent ceiling mounting
If there is already a mounting point in the middle of the ceiling, a standard projector with a zoom lens gives you the most positioning flexibility. A throw range such as 1.48–1.78:1 means one ceiling point can serve several image sizes.
Very large images for big audiences
For screens of 150 inches and up in halls or ballrooms, throw distance becomes an advantage: the projector sits behind the audience or at the operator's desk, well away from foot traffic. The bright classes for large venues are covered on the projector pricing page.
Budget
In our fleet, entry-class standard units are the most economical, while short throw and UST sit in higher rate classes. If your room has enough distance, paying more for a short throw brings no extra benefit.
Short Throw or Ultra Short Throw?
UST is the extreme version of short throw: the projector sits directly below the screen and projects upward at a very steep angle. Presenter shadows all but disappear, and a 100-inch screen can be filled from tens of centimetres away.
There are two consequences. First, the screen surface must be genuinely flat, because the steep angle turns every ripple in the fabric or panel joint into a visible shadow. Second, the unit's position is very sensitive: move it a single centimetre and the image can tilt or lose focus. UST makes most sense for very shallow rooms, interactive classrooms and showrooms. For meeting rooms with around one to two metres to spare, an ordinary short throw is enough.
Mounting Height, Offset and Keystone Correction
Besides distance, the projector's vertical position decides whether the image lands squarely on the screen. Almost every projector has an offset: the image is thrown slightly upward from the lens when the unit sits on a table, or slightly downward when it is mounted upside down on the ceiling. That is why a table-top projector should sit level with or slightly below the bottom edge of the screen, and a ceiling unit level with or slightly above the top edge.
Digital keystone correction can straighten a tilted image, but it does so by compressing pixels, which makes small text less crisp. Getting the position right always beats correcting it. Some higher-end models have lens shift, which moves the image optically without losing sharpness. On a short throw, the correction needed is usually more precise, because a small movement of the unit causes a large change in the image.
The Screen Surface Matters More with Short Throw
A short throw projects at a sharper angle, so any unevenness in the surface creates small shadows that are far more visible than with long-distance projection. Textured walls, walls with panel joints and patchy paint are best avoided. A screen with a flat surface gives a much cleaner result.
Surface colour matters too. A neutral white surface gives the most accurate colour, while a coloured wall shifts the whole image. Screen fabric also has a reflectivity value called screen gain; a matte white fabric with a gain of about 1.0 reflects light evenly across the seating angles. If the room cannot take a proper screen, describe the surface when you request a quote.
Brightness Is a Separate Calculation
Throw type and brightness are two different decisions that often get mixed up. Distance decides whether the image can reach the size you want; brightness decides whether that image stays readable under the room lights.
A common mistake is to choose a short throw for a small room and then pick the lowest brightness class, on the assumption that small rooms need less light. What actually matters is ambient light, including windows and lights that cannot be switched off. A brightness table by room type is in our guide to projector lumens for seminars. For very small, bright rooms, a TV screen is sometimes more practical; the comparison is in our projector vs TV for presentations article.
Rental Cost by Throw Type
Arental's rental rates follow the class of the unit, mainly its brightness and light source, rather than the throw type alone. Here is the picture from the current fleet:
| Type | Example unit | Per day | Per month |
|---|---|---|---|
| Entry-class standard | Epson EB-X06/W06, 3,700 lumens | Rp 60,000 | Rp 300,000 |
| Short throw | BenQ Short Throw | Rp 100,000 | Rp 500,000 |
| Ultra short throw | Epson EB-810E/815E, laser | Rp 200,000 | Rp 1,000,000 |
These are base rates per unit taken from each model's catalogue page. Exact pricing depends on specification, duration and unit count; delivery charges and applicable taxes are itemised in the quote. For a one-day event with a screen, the projector-plus-screen packages, which include delivery, setup and pickup, are listed on the projector rental prices page.
What to Measure Before Requesting a Quote
A few minutes with a tape measure saves a long exchange of messages. Send the following details with your request:
- Distance from the mounting point to the screen surface, measured horizontally, not diagonally.
- Width of the screen or wall available, minus space for frames and furniture.
- Distance to the farthest viewer from the screen, to set the image size.
- Presenter position: standing in front of the screen, beside it, or seated.
- Mounting point: whether there is a ceiling bracket, and whether the ceiling may be drilled.
- Nearest power outlet and the cable route from the presenter's desk.
- Lighting conditions: windows, curtains and lights that cannot be switched off.
- Content format: 16:9, 16:10 or 4:3 slides.
With that information, our sales team can recommend the throw type, brightness class and screen size in a single quote.
Frequently Asked Questions
What is the projector distance for a 120-inch screen?
For a 120-inch 16:9 screen about 2.66 metres wide, a projector with a 1.5 ratio needs about 4 metres, a 1.3 ratio about 3.45 metres, and a 0.5 short throw about 1.33 metres. On a 4:3 screen 2.44 metres wide, a 1.5 ratio needs about 3.66 metres.
How do I calculate projector-to-screen distance?
Convert the screen's diagonal into width (16:9: × 0.87; 16:10: × 0.85; 4:3: × 0.8; then × 2.54 for centimetres), then multiply that width by the throw ratio on the projector's spec sheet. For a zoom lens, use both the smallest and the largest ratio to get the minimum and maximum distance.
What is a short throw projector?
A short throw projector has a small throw ratio, usually around 0.4 to 1, so it can produce a large image from a short distance. A 100-inch screen can be filled from roughly 1 to 2 metres away, while a standard projector needs roughly 3 to 4 metres.
What is the ideal projector distance for a 100-inch screen?
It depends on the throw ratio. For a 100-inch 16:9 screen about 2.21 metres wide, a 1.5-ratio projector needs about 3.3 metres, a 1.8 ratio about 4 metres, and a 0.5-ratio short throw about 1.1 metres. Simply multiply the throw ratio on the spec sheet by the screen width.
Does a short throw produce a worse image?
Not in itself. Sharpness comes down to resolution, brightness and the condition of the screen surface, not the throw distance. What does need attention is the surface, which must be flat because the short throw's steep angle makes any unevenness more visible.
Can a standard projector be used in a small room?
It can, but the image will be small because the distance is not enough. From 2.5 metres, a 1.5-ratio projector only produces an image of about 75 inches. Forcing it usually ends with people at the back struggling to read the text.
Does a short throw need a special screen?
It is strongly recommended. Because of the steep angle, textured walls or wavy fabric create small shadows in the image. A flat tripod or wall-mounted screen gives a much cleaner result.
How do I read the throw ratio on a projector spec sheet?
Look for the "throw ratio" line, usually written as something like 1.48–1.78:1. The first number applies at the widest zoom setting and the second at the narrowest. Multiply both by the image width to get the nearest and farthest mounting distances.
References & Sources
To work out the throw distance and image size for a specific projector model before requesting a quote, use the Projector Central projection calculator (accessed 21 November 2026). The throw ratios of the units in the tables are taken from the specifications on Arental's catalogue pages.
The Epson EB-W06 throw ratio (1.30–1.56) follows Epson's official specifications (accessed 21 November 2026).